Alloy Steel WP5 Buttweld Fittings Manufacturer

Sachiya Steel International Is One Of The Leading Manufacturer And Exporter Of High Quality Alloy Steel WP5 Buttweld Fittings, which has good and excellent resistance to oxidation. These Alloy Steel WP5 Elbow Butt Weld Pipe Fittings is approved for service up to 600 Degree F, where its Melting point is 2615 Degree F -2635 Degree F. Our Alloy Steel WP5 Tee Butt Weld Pipe Fittings may perhaps be used in continuous service up to 1140 Degree C provided reducing Sulphur gases are not present.

Alloy Steel WP5 Buttweld Fittings Manufacturer In India | Alloy Steel WP5 Buttweld Fittings Manufacturer In Mumbai | Alloy Steel WP5 Buttweld Fittings Exporter In India | Alloy Steel WP5 Buttweld Fittings Exporter In Mumbai | Alloy Steel WP5 Buttweld Fittings Supplier In India | Alloy Steel WP5 Buttweld Fittings Supplier In Mumbai | Alloy Steel WP5 Buttweld Fittings Stockist In India | Alloy Steel WP5 Buttweld Fittings Stockist In Mumbai 

 

Alloy Steel WP5 Buttweld Fittings
 Alloy Steel WP5 Buttweld Fittings

These Alloy Steel WP5 Cross Butt Weld Pipe Fittings is used for a variety of processing equipment, particularly to maintain product purity in handling foods, synthetic fibers and alkalis. By means of its high chromium content, our Alloy Steel WP5 Reducer offers good corrosion resistance to increase high temperature properties. During outdoors, the rate of attack in these Alloy Steel WP5 Stub End is slow because of the formation of a thin protective film, usually a sulphide.

Our Alloy Steel WP5 End Cap Butt Weld Pipe Fittings normally remains bright in indoor atmospheres, where corrosion rates in both marine and rural atmospheres are very low. These Alloy Steel WP5 Seamless Pipe Fittings was a modification of 200 to control carbon which keeps it from being embrittled by inter – granular precipitates at temperatures of 600 Degree F to 1400 Degree F in many processes.

What is WP5 steel?

WP5 is a steel grade. W stands for weldable, P represents for pressure, and 5 stands for grade. The material used in the pressure pipe system in average and higher temperature services.  

What is the difference between galvanized steel and carbon steel?

Galvanized steel is the superior choice over untreated carbon steel for job locations exposed to acid rain, road salt, and sea water due to the layer of zinc which serves as protectant from corrosion.

Alloy Steel WP5 Pipe Fittings Specifications
Specifications : ASTM A234 / ASME SA234
Size : 1/8” NB TO 48” NB. (Seamless & 100% X-Ray Welded, Fabricated)
Standards
: ASME/ANSI B16.9, ASME B16.28, MSS-SP-43
Thickness : Sch 5s, Sch 10s, Sch 40s, Sch 80s, Sch 160s, Sch XXS
Type : Seamless / Welded / Fabricated

Alloy Steel WP5 Pipe Fittings Chemical Composition

Grade C Mn Si S P Cr Mo
A234 WP5 ≤0.15 ≤0.6 ≤0.5 ≤0.04 ≤0.03 4-6 0.44-0.65

Alloy Steel WP5 Buttweld Fittings Mechanical Properties

Grade Tensile Strength (Mpa) Yield Strength (Mpa) Elongation %
A234 WP5 415 – 585 ≥205 ≥20

ASTM A234 WP5 Pipe Fittings Size Chart

O.D. or I.D. Diameter Equivalent Decimal Nominal Diameter Typical Threads In Inch
5/16 0.313 1/16 27
13/32 0.405 1/8 27
35/64 0.540 1/4 18
43/64 0.675 3/8 18
27/32 0.840 1/2 14
1-3/64 1.050 3/4 14
1-5/16 1.315 1 11-1/2
1-21/32 1.660 1-1/4 11-1/2
1-29/32 1.900 1-1/2 11-1/2
2-3/8 2.375 2 11-1/2
2-7/8 2.875 2-1/2 8
3-1/2 3.500 3 8
4 4.000 3-1/2 8
4-1/2 4.500 4 8

Alloy Steel WP5 Fittings Tolerances Chart

 

ASTM A234 WP5 Pipe Fittings (Grade WP5 To WP91) Tolerance 90 Deg And 45 Deg
Elbows And Pipe Tee
Reducer (Concentric/ Eccentric)
& Lap Joint
Stub End (Long / Short)
Pipe End Caps
Normal Pipe Size (NPS) Of ASME B16.9 O. (Outside)
D. (Diameter)
at Bevel
I. (Inside)
D.(Diameter)
at End
Wall Thickness Of T Center-to-End
Dimension
A ,C ,B
Over-all
Length Of H
Over-all
Length Of F
1/2 to 2-1/2 +0.06 Not less than 87.5%
of nominal thickness
+/- 0.06 +/- 0.06 +/- 0.12
-0.03
3 to 3-1/2 +/- 0.06 +/- 0.06 +/- 0.06 +/- 0.06 +/- 0.12
4 +/- 0.06 +/- 0.06 +/- 0.06 +/- 0.06 +/- 0.12
5 to 8 +/- 0.06 +/- 0.06 +/- 0.06 +/- 0.06 +/- 0.25
10 to 18 +0.16 +/- 0.12 +/- 0.09 +/- 0.09 +/- 0.25
-0.12
20 to 24 +0.25 +/- 0.19 +/- 0.09 +/- 0.09 +/- 0.25
-0.19
26 to 30 +0.25 +/- 0.19 +/- 0.12 +/- 0.19 +/- 0.38
-0.19
32 to 48 +0.25 +/- 0.19 +/- 0.19 +/- 0.19 +/- 0.38
-0.19

Alloy Steel WP5 Buttweld Pipe Fittings Application Industries

 

  • Off-Shore Oil Drilling Companies
  • Power Generation
  • Petrochemicals
  • Gas Processing
  • Specialty Chemicals
  • Pharmaceuticals
  • Pharmaceutical Equipment
  • Chemical Equipment
  • Sea Water Equipment
  • Heat Exchangers
  • Condensers
  • Pulp and Paper Industry

Alloy Steel WP5 Buttweld Fitting Test Certificates

 

We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.

• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc

Material Testing

We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.

• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test

Documentation

• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)

Alloy Steel WP5 Buttweld Fittings
Alloy Steel WP5 Buttweld Fittings

Sachiya Steel International Is One Of The Leading Manufacturer And Exporter Of High Quality Alloy Steel WP5 Buttweld Fittings, which has good and excellent resistance to oxidation. These Alloy Steel WP5 Elbow Butt Weld Pipe Fittings is approved for service up to 600 Degree F, where its Melting point is 2615 Degree F -2635 Degree F. Our Alloy Steel WP5 Tee Butt Weld Pipe Fittings may perhaps be used in continuous service up to 1140 Degree C provided reducing Sulphur gases are not present.

Product Brand: Sachiya Steel International

Product In-Stock: InStock

Editor's Rating:
5

Leave a Reply